AC servo motor drive and 130 flange servo motor 1KW 4N.m complete set of servo system to send 3 wire
Servo drive main control mode:
1, position pulse control: there are three kinds of pulse plus direction (CP + DIR); positive and negative control (CW + CCW); 90 ° orthogonal pulse (A + B).
2, analog speed control, analog 0-10V voltage control motor speed, you can achieve positive and negative and return to zero (or quasi-stop) function.
3, the internal speed control, by setting the drive parameters to specify the motor speed. Up to 8 steps can be set in advance.
4, the location of fixed length control, by setting the parameters of the drive to specify the motor movement distance and speed, you can achieve positive and negative movement.
5, to achieve the spindle servo function, you can achieve speed control and position control switching, quasi-stop function. (Note: need this function, please contact customer service, universal type is not with this function.)
A customer asked:
Why are your prices doing so low? What about product quality?
1: In management, we use flat management, making the operating costs greatly reduced.
2: We use the network direct sales model, reduce the cost of intermediate links will leave the profits to customers.
3: Components We are using the world famous brands, to ensure stable and reliable drive performance.
4: PCB process we use the immersion process, SMT chip processing.
Servo drive main core components:
1: using TI's (DSP) digital signal processor and ALTERA complex programmable logic device (CPLD) as an arithmetic unit
2: filter capacitors imported from Japan, the original ruby aluminum electrolytic capacitors
3: Current sensor using Honeywell HoneyweLL
4: Japan's Mitsubishi Intelligent Power Module (IPM)
5: PCB board using immersion gold process
6: the use of aluminum alloy shell, making the heat effect is very good.
7: Servo motor using Japan's TAMAGAWA incremental photoelectric encoder
1, a servo motor
2, a servo drive
3, one encoder line (3 meters)
4, a motor power cord (3 meters)
5, 25 core parallel port one
6, a manual
1. Air outlet is the use of strong brand, (gold)
2. Enameled wire used 180T, high temperature 180 degrees
3. Rare earth permanent magnet material is a listed company in Jiangxi, model SH-T, each piece of magnetic flux difference of not more than 1% (stability), 150 high temperature oven baking 2 hours, repeated three times, and then test permanent magnet Material, demagnetization rate of not more than 3%
Servo drive model: DA98
Power: The servo drive adapter power is 1.2KW ~ 2.6KW motor
Independent research and development of a new generation of all-digital AC servo drive, mainly using the latest digital signal processor DSP technology and large-scale programmable FPGA technology as the core of the computing unit, and intelligent IPM power module, with fast response, perfect protection, high reliability A series of advantages.
Speed ??ratio of 1: 5000, from low to high speed have a stable torque characteristics
Control positioning accuracy ± 0.01%, 300% overload capacity
Using space vector control algorithm, than the average SPWM generated by the greater torque, less noise
Perfect protection: overcurrent, overvoltage, overheating and encoder failure
A variety of display functions: including motor speed, motor current, motor position, position deviation, pulse number, pulse frequency, linear speed, input and output interface diagnostics, historical alarm records
The DSD10 servo drive is a base mounted servo drive
Storage conditions: When storing the servo drive in a non-energized state, store it in the following temperature range: -20 to +85 ° C.
Environmental conditions in the control cabinet:
1. Ambient temperature of servo drive: 0 ~ 55 ℃
2. Humidity: 90% RH (relative humidity) or less
3. Vibration: 4.9m / s2
4. Do not appear to freeze, condensation and so on
5. To ensure long-term reliability, use at ambient temperatures below 45 ° C
And the analog command input circuit interface: analog signal is the speed command signal and torque command signal, the command input impedance of about 40kΩ, the maximum allowable input voltage of ± 10V interface with the input circuit: the use of a relay or open collector transistor circuit To connect. When using the relay connection, select the relay for the small current. If you do not use a small current relay, it will cause poor contact. (PAO, / PAO, PBO, / PBO) and the origin pulse signal (PCO, / PCO) of the encoder's 2-phase (A-phase, B-phase) pulse are output via the bus driver Circuit for output. Usually used when the upper device side constitutes a position control system. On the upper device side, use the line receiving circuit to receive. Interface to the output circuit: Servo alarm, servo readiness, and other sequence The output signal consists of an optocoupler output circuit. Use the relay, wire receiver circuit connection.
Automatic tuning of responsiveness can be achieved by using the inertial identity function of the new algorithm and the five tuning feature selections, the 30-level responsiveness setting or the automatic saving function using the parameters.
Control mode switch
Position control, speed control, force control.
Power harmonic countermeasures
The standard is equipped with a DC choke coil connection terminal as a power supply harmonics.
6-digit display LED, built-in operation keyboard
Can be set up or monitored in the field easily. You can use the built-in keyboard to change the parameters, monitoring devices and alarm tracking adjustment.
With the feedforward damping control, the vibration of the machine front and the vibration of the frame can be suppressed by a simple adjustment. At the same time, four frequencies can be set and selected to control the vibration.
Shorten the positioning set time
By adopting the new algorithm, the positioning and setting time of the device can be greatly reduced.
Shorten the positioning set time
Instruction tracking suppression
With the new position and algorithm, the position suppression tracking capability can be increased to twice that of the existing model, and the zero position deviation can be basically achieved.
Instruction tracking suppression
Commissioning function (jogging function)
It is possible to confirm the operation of the motor and the amplifier, and it is not necessary to connect with the host device.
Consejos p á RR algunos clientes:
- Brasil : Por favor, inf óleo Leo rmenos el CNPJ (empresa) o ACB (privado) despu é s de realizar el pedido.
- Argentina : Por favor, inf óleo Leo rmenos su CUIT despu é s de realizar el pedido.
- Ruso : Es mejor tener un nombre de la empresa, o por lo menos su nombre completo.