Hongkong Royal Machinery Parts Co., Ltd.

China Manufacturer with main products: 2 Phase Hybrid Stepper Motor, 3 Phase Stepper Motor, Gearbox Stepper Motor, Stepper Motor Drivers

Home  >Products Catalog > 2 Phase Hybrid Stepper Motor > 24~50V DC brushless motor controller

24~50V DC brushless motor controller

Payment Terms: L/C

Related products from verified members

Place of Origin: Beijing in China

Specifications

 

DC brushless motor controller Features

  • SPWM, Speed/Current alike close loop technology, smooth rotation
  • Smooth torque output within speed range (8000 rpm Max.)
  • 1:75 Max. speed regulation ratio
  • 60°/300°/120°/240°Electrical angle adjustable
  • Speed regulation: potentiometer adjust / Analog input
  • Run/Step, Quick Brake, CW/CCW rotation shift
  • Speed output, Alarm output(O.C.)
  • Over current, over voltage, stall, missing speed Alarm

 

Parameters
Electrical Parameters(Tj=25ºC)

Power

24~50VDC,  Capacity:up to motors

Current output

Rated 15A, Peak 45A(≤3s)

Driving mode

SPWM 

Insulation Res.

>500MΩ

Dielectric Strength

500V/Minute

Weight

About 300g

Ambient requirement

Cooling

Self cool

Environment

Keep away from oil,  dust,  and acid gas

Temperature

0ºC~+50ºC

Humidity

<80%RH

Vibration

5.7m/s2.Max.

Storage temp.

-20ºC~+125ºC 

Function description

  • Power Supply: DC+ ; DC-

Voltage: 24~50DC, normally Linear Power Supply applied(appendix), ripple voltage higher than 50V may damage driver. The output current of LPS shall be 60%more than that of driver. In case of switching power supply(strongly recommended)applied, please pay attention to the current shall meet motor’s current.
Attention: incorrect connection may cause driver damaged.

  • Speed regulation choice(RV ; AVI)

1.Setup speed by potentiometer (RV).The dipswitch SW2 must be ON status to enable this function. CW rotate the potentiometer will increase speed. CCW- speed down.

2.Setup speed by analog input (AVI). The dipswitch SW2 must be OFF status to enable this function..AVI terminal accept 0~5V voltage or PWM signal from controller.AVI terminal with input resistance of 100K, current consumption≤5mA.

Reference table

SW2

Command to

Speed adjust

Comman

Current

ON

RV

CW—speed up, CCW—speed down

OFF

AVI

0~5V analog input

0~5V volage

≤5mA

OFF

AVI

PWM

1KHz duty cycle

Only one of above two modes can be used to adjust speed (another mode shall be enabled). Once AVI terminal applied, (RV) potentiometer shall be CCW turned to Min. position.PWM signal are 5V TTL level.

 

  • Run/Stop(ENBL)


ENBL terminal is applied to control motor Run/Stop, Common positive terminal is +5V.

Optical coupler short circuit make motor run, it open circuit make motor stop.

See below circuit
    

  • CW/CCW Rotation(F/R)

    
F/R terminal is applied to shift motor rotate direction, common positive terminal is+5V.
    
Motor run in CCW when optical coupler is short circuit, motor run in CW when optical coupler is open circuit.
    
Attention:don’t change the connection sequence of phase wires of motor to shift rotate direction.

  • Motor Brake Command(BRK)


BRK terminal applied to stop rotation quickly. Motor will stop normally within 50ms. But inertia of load can’t exceed 2 times of motor inertia, otherwise brake will cause driver alarm.

Time of acceleration and deceleration must be put into controller in case of too big load inertia,

And please don’t use brake function in such condition.

The optical coupler short circuit will brake motor, optical coupler open circuit release motor to run.

  • Setup different electrical angle


Dipswitch SW1 can be setup to fit motors with different electrical angel

SW1

 

ON

120°or 240°hall signal, they are in opposite rotation direction

OFF

60°or 300°hall signal,  they are in opposite rotation direction

 

  • Motor rotation speed output(SPEED)


Pulse generated by driver are proportioned with motor speed, (isolated O.C. output) it can be increased to be a random level. 6 multiple frequency processed output.

Motor speed=60×SPEED(pulse freq.)/pulses per rev. of motor; p.p.r=motor pole pairs×6

  • Alarm output(ALM)


Driver will enter protection mode and stop motor running in case of OVER CURRENT, OVER VOLTAGE, SHORT CIUCUIT, MOTOR STALL arise, LED on driver will be light, and ALM signal will be available. Please cut off driver’s power supply, check wiring and voltage. High voltage is not permitted for big inertia motor, as it may cause run/stop frequently and over voltage alarm.  Circuit of this function refer to pic. 2.
    
    
    

  • Terminals description

Terminal mark

Description

DC+; DC-

Voltage supply to driver

U; V; W

To motor leads. Make sure correct connection to motor leads.

REF+; REF-; HU; HV; HW

Hall sensor connection, REF+;
REF- are for hall power supply. Make sure correct connection to halls.

AVI; ENBL; F/R; BRK; Vcc

Controls input, see below picture

SPEED; ALM

Signal output, (O.C.)

 

  • Wiring Diagram

Dimension

Service Process

Service Guarantee

  • Free Service Charge

    ECVV doesn't charge any service fee to Buyers for buying this product.

  • ECVV Supply

    ECVV is responsible for supply, and provides product quality inspection, fund supervision and supply chain services.

  • Product Quality Commitment

    ECVV China Sourcing Agent will assess the reputation and supply ability of the factory and conduct field trips to select the high-quality Chinese factories for buyers.

  • Deposit Service Commitments

    In order to improve the quality of service, ECVV will charge for a 100CNY deposit for the agent purchasing order, and the deposit will be part of subsequent purchasing costs.

    After paying a deposit, if the purchasing order is not completed because of unsatisfied ECVV services, ECVV will refund your deposit.

Ecvv Trade

Brushless Dc Motor Controller from this supplier

Forklift Truck Attachment Sideshifter    
FOB Price: 1.00-500.00 USD/Parcel
Min Order: 1 Parcel
Sell the Machine for Making Melt-Blown Fabrice More Than 95    
FOB Price: 100.00-100000.00 USD/Piece
Min Order: 1 Piece
High Speed Mask Production Machine    
FOB Price: 50000.00-100000.00 USD/Set
Min Order: -1 Set
Plastic Five Arm Knob Plastic Five Star Handle Knobs for Tools    
FOB Price: 0.21-0.81 USD/Piece
Min Order: 20 Pieces
China Automatic Ss Tank Polish Buffing Machine for Pharmaceutical Equipment Beer Brewery Factory    
FOB Price: 9999.00-14999.00 USD/Set
Min Order: 1 Set

More products from other suppliers

Induction Welding Machine for Crystal    
FOB Price: 10.00-1000.00 USD/Set
Min Order: 1 Set
6-key controller    
FOB Price: 50.00-100.00 USD/shenzhen
Pass Box    
Auto feeder    
FOB Price: 100.00-2,000.00 USD/Set
Min Order: 1 Set
Light Fastness Tester    
FOB Price: 38,462.00-49,231.00 USD/Set
Min Order: 1 Set
112mm Drag Bit    
FOB Price: 50.00-300.00 USD/Piece
Min Order: 1 Piece
Automatic Carton Erector    
FOB Price: 1.00-10000.00 USD/Set
Min Order: 1 Set

Can't find a suitable Supplier or product? Entrust ECVV to purchase the well-chosen Chinese products with high cost performance.

Learn More>> Start Safebuy Order

Communicate with Supplier

Lily from ECVV
Join ECVV community
Join Facebook Group